AGP Picks
View all

Guide explains hot-dip galvanizing process and coating standards

Oct. 20, 2026
Guide explains hot-dip galvanizing process and coating standards
By AI, Created 09:30 UTC, Oct 20, 2026, AGP -

A new technical guide from Handan, Hebei lays out the steps, equipment and timing behind hot-spray zinc anti-corrosion work. It also argues that the method can improve adhesion, reduce deformation and support field repairs compared with conventional galvanizing approaches.

Why it matters: - Hot-spray zinc is presented as a corrosion-protection method for steel structures that can address coating adhesion, repairability and workpiece size limits. - The guide says the process can reduce deformation because it uses low temperatures, and it can support on-site repairs after installation or transport damage. - The article also frames the method as a cleaner option than cold-dip galvanizing because it relies on sandblasting pretreatment instead of pickling and phosphating.

What happened: - The guide was issued from Handan, Hebei, China, on October 20, 2026. - The article explains the principle of thermal zinc spraying as sandblasting a workpiece first, then spraying atomized zinc onto the metal surface with a spray gun. - The process uses oxygen, acetylene or an electric heat source, with electric heating for large workpieces and oxygen-acetylene heating for small and medium-sized workpieces. - The construction process is divided into four steps: surface treatment, zinc spraying, sealing treatment and quality inspection.

The details: - Surface treatment must remove rust, scale, grease, dirt, paint and other attachments. - Rust removal follows the Sa3 standard in GB8923-88, “Rust Grades and Rust Removal Grades for Steel Surfaces Before Painting.” - After sandblasting, the surface should show a uniform metallic luster and be cleaned with dry compressed air or a clean brush. - The sandblasting setup includes an air compressor, air tank, oil-water separator, air filter, sandblasting pot, adhesive tape, sandblasting gun and wear-resistant porcelain nozzle. - The abrasive is described as high-hardness, angular river sand sized 0.5-2 mm. - The sand should be dry, with moisture content below 1%, and free of impurities. - The nozzle uses an expanding L-shaped porcelain design that drives air to supersonic speed and increases the kinetic energy of the abrasive. - The sandblasting process is said to improve activation of the substrate surface and increase coating bonding strength. - The guide says surface treatment can reach Sa3 standards and a roughness of 40-60 µm. - Zinc spraying should happen within 2-3 hours after sandblasting. - The guide says the substrate surface is most active in that window, when bonding strength is highest and the oxide film is still thin enough to be broken by sprayed particles. - The zinc-spraying equipment uses a domestically produced spray gun, described as typically a Zhonglian air handheld spray gun from the Shanghai Spraying Machinery Factory. - The zinc wire should be oil-free, 3 mm in diameter, and contain at least 99.5%-99.7% zinc. - The article lists a tensile strength of at least 6 MPa for the coating adhesion achieved through sandblasting pretreatment.

Between the lines: - The article is promotional in tone, but the technical emphasis suggests the main selling points are adhesion, surface cleanliness and lower thermal stress. - The comparison with cold- and hot-dip galvanizing positions zinc spraying as more flexible for fabrication and repair work, especially when tank dimensions or site conditions are limiting. - The claim that hot-dip galvanizing will become increasingly popular reflects the article’s forecast, not a measured market outcome.

What's next: - The guide indicates the critical control points are pretreatment quality, the short time window before spraying and post-spray inspection. - Users following the process are expected to complete zinc spraying within 2-3 hours of sandblasting to preserve adhesion. - The article concludes that hot-spray zinc anti-corrosion work should proceed through surface treatment, zinc spraying, sealing and quality inspection for best results.

The bottom line: - The guide argues that hot-spray zinc offers a practical anti-corrosion path for steel structures when strong adhesion, low deformation and field repair matter most.

Disclaimer: This article was produced by AGP Wire with the assistance of artificial intelligence based on original source content and has been refined to improve clarity, structure, and readability. This content is provided on an “as is” basis. While care has been taken in its preparation, it may contain inaccuracies or omissions, and readers should consult the original source and independently verify key information where appropriate. This content is for informational purposes only and does not constitute legal, financial, investment, or other professional advice.

Sign up for:

Jobs & Careers: Asia

The daily local news briefing you can trust. Every day. Subscribe now.

By signing up, you agree to our Terms & Conditions.

Share this page:

Advanced Search Options

Search for:

Search scope:

Type:

Search in:

Date range:

The last

Sort by:

Sign up for:

Jobs & Careers: Asia

The daily local news briefing you can trust. Every day. Subscribe now.

By signing up, you agree to our Terms & Conditions.